Bird Divided Tool Caddy Box ~ Part 1

57

This workshop shows how to cover and make up the tool caddy and part 2 will provide the know how on how to make some dividing panels for the Creative Expressions MDF tool caddy.

58

Here are the moveable section panels which are ideal for adding in and taking out as and when you need to.

_________________

Click on the link below for a Printable Version of the Workshop

Bird Divided Tool Caddy Box Part 1

 ________________________

If you have a Facebook account

you can now follow Creative Expressions on FACEBOOK

Click here for the link

Great for latest information

_______________

Shopping List

 Grand Calibur™ Die Cutting Machine : WIZGC-200

Creative Expressions MDF Tool Caddy : CEMDFTOOLCAD

Craft Consortium Decoupage Papers ~ Oakwood : CCDECP084

& Birds & Butterflies : CCDECP142

Cosmic Shimmer Gloss Glue, Seal & Glaze :  CSGLOSGLUE or

Cosmic Shimmer Matt Glue, Seal & Glaze : CSMATTGLUE

Flat Paint Brush Section 

Sanding Block : CO723060

Creative Expressions Tags & Frames ~ Zoe Die Set : CED4310

Phill Martin Chic Moss Gilding Wax : CSPMGWMOSS

 Spellbinders All-in-One Tool : WIZTOOL

Creative Expressions Smoothies Mini`s 4 per pack : CESMOOTHMINI or

Standard 2 per pack : CESMOOTH

Tim Holtz Tattered Rose Ink Pad : DPTATTROSE

Creative Expressions Finishing Touches Off White Satin Ribbon : CESROFFWHT

    Cosmic Shimmer Clear Glue : CSGLUE,

Cosmic Shimmer Pearl PVA White Glue : CSPEAWHGLU  & Silicone Glue

Foundations Coconut Card : 40980

Creative Expressions Finishing Touches White Pearl Corners ~ Design 2 : SASCW2

      ___________________

Step by Step Instructions

Step 1. This workshop shows how to cover and make up the tool caddy and part 2 will provide the know how on how to make some dividing panels for the Creative Expressions MDF tool caddy. For the project you will need the following key products. The Creative Expressions MDF tool caddy , the Craft Consortium decoupage papers ~ oakwood & birds and butterflies adhered using the Cosmic Shimmer matt glue, seal & glaze. The tag has been created using the Creative Expressions tags & frames ~ Zoe die set.

11

Step 2. Shake the glue / glaze bottle well and here I have got an empty embossing powder pot ready ~ so never throw them away as they are so useful for glue pots or mixing embossing powders and micas in.

2 2

Step 3. Pour some of the glue / glaze into an empty pot.

3 3

Step 4. Select the Craft Consortium decoupage papers ~ oakwood & birds and butterflies. The oakwood paper will give a nice back drop to showcase the birds and butterflies paper on the rest of the tool caddy. It will also mean you can get the whole caddy decorated in one pack of the birds and butterflies and use 1 sheet of the oakwood decoupage papers.

4 4

Step 5. Tear the oakwood decoupage so it is just a bit bigger than the central tool caddy MDF piece as this will make it easier to handle when gluing down. Make your mind up which direction you wish the wood effect to fall, I prefer the upward position.

5

Step 6. Brush the Cosmic Shimmer matt glue, seal & glaze over both the main central panel of the tool caddy making sure you go right up to the edge of the MDF. Use the glue sparingly as over loading will make the thin decoupage paper crinkle up more.

66

Step 7. Place the oakwood decoupage paper down onto the glued MDF panel.

77

Step 8. Sweep the oakwood decoupage paper down smoothly as you go. If there is a ruffle then lift the paper and ease it back down so it eliminates the air bubbles or issues in the paper.

8 8

Step 9. Cut a slit in the decoupage paper which falls in the handle part of the tool caddy. Now the paper can be moulded in place over the edges of the handle ready to be sanded.

9 9

Step 10. Take the sanding block and hold it at a 45 degree angle & sand downwards over the edge of the MDF to create the smooth finish. You will need to work around the notches and a great tip for the small areas is to use a emery board nail file (not a metal one) or a loose piece of sandpaper folded in half.

10 10

Step 11. You will be left with a lovely smooth covered MDF panel. Repeat the process and cover the reverse of the piece.

11 11

Step 12. Put together the pieces of the tool caddy MDF set together omitting the central just covered piece. You will see when doing this there is a correct way the pieces should go with the long rectangle pieces.

12 12

Step 13. For ease of covering the caddy and so that the full decoupage sheets are placed on the outside, place a mark on each of the outside panels, a`*` works well.

13 13

Step 14. Take all the pieces apart and lay all the `*` marked sides upright on the craft table.

14 14

Step 15. Lay 2 sheets of the birds and butterflies decoupage sheets over the larger side panels so that one sheet is on top of the other. Cut the sheet so that there is just a small excess of the decoupage paper all around the edge of the MDF panels.

15 15

Step 16. Repeat the process of covering the panel using the glue/glaze and the sanding technique as you have done on the central MDF panel.

REMEMBER if you want a completely covered side piece only sand down the inner slot and retain the outer decoupage paper to cover the slots up nicely when the caddy is all put together later on.

16 16

Step 17. Lay the top area of the birds and butterflies decoupage paper which was left over and place it over the rectangle front & back `*` panel of MDF and cover using the glue/glaze technique.

17 17

Step 18. Use the large off cuts to cover the inner top of the base MDF panel as you can run a line of the glue/glaze over the edge of the decoupage papers and then stick the other piece of paper over the glued area. As it`s the inside of the tool caddy it doesn`t matter so much as you will find it hard to know it`s got a join if you keep the birds all in the same line.

18 18

Step 19. Poke the paper through on all the slots of the domed panel and use the paper nail file if you are not retaining one side covered in the decoupage paper.

19 19

Step 20. This will burnish the edges of the paper onto the glue and seals the edges down smoothly.

20 20

Step 21. Complete all of the slots on both panels.

21 21

Step 22. Once the 2 fronts are done now cover the reverse of the panels.

22 22

Step 23. As there is no pieces of the paper left which will cover the inside of the domed MDF piece then take a strip of the paper and glue in down the edge of the piece and lay some glue over the top of the paper on the left hand side of the paper. Then use the other larger piece of paper to cover the area.

23 23

Step 24. Continue to work through the MDF pieces and cover the panels as needed. I haven`t covered the underneath of the tool caddy as it won`t be seen and it will save on the decoupage papers !!!

24 24

Step 25. Lay the end panel down on the work surface and place the base panel on before adding the 2 shorter panels. You can use glue but I like to add the pieces in place first.

25 25

Step 26. Now place the centre oakwood piece in the slots.

26 26

Step 27. Before adding the other side panel to complete the basic shape of the caddy.

27 27

Step 28. As mentioned before you can leave one side with the paper covering the slots as this would be the look if not. I like this feel as it matches the oakwood paper.

28 28

Step 29. If you don`t then place a small amount to the glue/ glaze and add a piece of the decoupage paper over the slot.

29 29

Step 30. Use some Cosmic Shimmer dries clear glue or as here the Cosmic Shimmer pearl PVA glue to run a line along the front edge of the tool caddy as they will strengthen the piece together. Part 2 of the workshop will show you how to make covered sections for the caddy so it`s makes different additional sections in the box as this will customise it to your own needs.

30 30

Here is the completed project which will be finished off in part 2 next week so please check back in or subscribe to have a weekly e-mail directly to you with the workshop there for you to view.

57

Part 2 will follow next week ~ This will show you to make the section panels to compliment the tool caddy design.

58

Happy Crafting

______________________

 Please subscribe to the Creative Expressions weekly workshop site in the e-mail section on the right hand side of the website

This means you will have the workshop e-mail straight to your inbox when it`s released at 00.30am on a Friday morning.

  __________________________

 Check out the new Clearance Craft site

Check it out Banner2

 __________________________

              For all the Indexed Weekly Workshops

Click here

mixed 1

_________________

If you have a Facebook account

you can now follow Creative Expressions on FACEBOOK

Click here for the link

Great for latest information

This entry was posted in Spellbinder Dies, Tim Holtz Distress Inks, Tim Holtz Idea-ology Range. Bookmark the permalink.